Recubrimiento Epoxi Alimentario – Europoxy Tankguard OW400
SKU:Special food grade epoxy coating for contact with wine and oil, bicomponent 100% solids with global and specific migration test. For interior coating of tanks or reservoirs in contact with food oils or fatty foods, wines, milk or alcoholic beverages (max. 20%). Also suitable for floors, walls and ceilings in food environments where it offers high hygienic properties.
- Color/Finish Oxide Red/Glossy Red
- Mix ratio 100/50 (A/B)
- Solids by weight 100%
- Recommended yield 4.1 m²/L
Description
Certified food grade epoxy coating with high chemical and abrasion resistance that withstands continuous temperatures of 50 ºC and peaks of up to 60 ºC without altering its properties.
Main uses
- Food industry, wine tanks, oil tanks, wine cellars, cold stores, warehouses, canneries, dairy industry, tank trucks, cooperatives, food tanks, alcoholic beverage tanks, chemical industry, laboratories, pharmaceutical industry.
- Painting in general for the interior coating of steel, concrete or mortar tanks or reservoirs that will contain oils and fatty foods such as milk, meats or alcoholic beverages such as wines and beers with a maximum alcohol content of 20%.
- For protection and repair of floors, baseboards and ceilings in food facilities, warehouses or canneries.
- Rehabilitation of oil mills, feed hoppers or machinery in cooperatives.
Official Certification
Product certified by external laboratory accredited by ENAC, for the performance of global and specific migration tests as determined by Regulation (EU) No 10/2011 of January 14, 2011 and Royal Decree 847/2011 for contact with food and alcoholic beverages. OTEC RIERA, reference no. 1037226552
* The product complies with current regulations. To see the complete certification and tests, please access the product data sheet.
Main features
- Does not contain organic solvents.
- Easily applied by brush, roller or air-less spray gun.
- Highly waterproof.
- Product with thixotropic rheology.
- Very good adhesion on different types of construction materials such as concrete, mortar, fiber cement, brick, wood, steel, etc.
- Good abrasion and impact resistance.
- Resists washing and scrubbing with normal detergents.
Application data
- Recommended coverage per coat 4.1 m²/L (for 250 μm dry in one coat).
- Total recommended coverage 500 - 1000 g/m2 applied in 2 or 3 coats.
- Recommended dry film thickness 200-250 microns.
- Mixing ratio (by weight) 100/50 (A/B)
- Pot life (Pot life) 20 ºC 35-40 minutes
- Recoating time (20ºC RH: 60%) between 12 and 48 hours.
- Cleaning solvent Green solvent
* Performance factors are approximate and depend on the conditions of the substrate and the absorption capacity of the substrate.
Drying and start-up times
- Curing temperature 25ºC
- Repainting times: Minimum 12 hours Maximum 2 days
- Commissioning time: Pedestrian traffic 2 days Immersion 5 days Total cure 10 days
Important Note: Do not place the tank or reservoir in service until the coating is fully cured, approximately 10 days at 25°C, and has been thoroughly washed several times with potable water. Placement in service may be longer if curing temperatures are low or thicknesses are greater than specified.
Instructions for use
- The product is presented in pre-dosed batches, respecting the mixing ratio to the maximum and taking special care to drag the remains adhered to the bottom and walls of the container.
- The mixing operation of the components is carried out mechanically until a homogeneous mixture is obtained, using a low speed mixer (600 rpm) equipped with propellers that do not favor the entry of air and the formation of bubbles. First, each component is beaten separately and then the component from the small container or component B is poured into the large container or component A, beating the mixture until it is completely homogenized (approximately 1-2 minutes).
- Product to use, does not require dilution.
- It should be taken into account that the pot-life of the mixture depends on the temperature(the higher the temperature, the lower the pot-life and vice versa).
- Apply by roller, brush or spray ensuring the formation of a continuous layer without pores.
