Recubrimiento Epoxi Alimentario – Europoxy Tankguard W300
SKU:Special two-component food grade epoxy coating for contact with drinking water, 100% solids with global and specific migration tests. Suitable for the interior coating of tanks, pipes or drinking water tanks, floors and walls located in food and sanitary environments. Withstands continuous temperatures of 50 ºC and peaks of up to 60 ºC without altering any of its properties.
- Color/Finish White/Glossy
- Mixing ratio 100/35 (A/B)
- Solids by weight 100%
- Recommended yield 4.1 m²/L
Description
CERTIFIED food grade epoxy coating for food and sanitary environments and drinking water tanks.
Main uses
- Food industry, water tanks, pipelines, cold rooms, industrial kitchens, warehouses, fish farms, dairy industry, health centers, veterinary centers, clinics, operating rooms, chemical industry, laboratories, pharmaceutical industry.
- Painting in general for the interior lining of tanks or reservoirs containing potable water.
- For protection and repair of floors, baseboards and ceilings in food or sanitary facilities, laboratories, health centers, hotels or kitchens.
- Inner lining for food grade pipes.
Official Certification
Product certified by an external laboratory accredited by ENAC, for the performance of the tests required by RD 3/2003 on water quality. OTEC RIERA, reference nº 1037126572
* The product complies with current regulations. To see the complete certification and tests, please access the product data sheet.
Main features
- Does not contain organic solvents.
- Easily applied by brush, roller or air-less spray gun .
- Highly waterproof.
- Product with thixotropic rheology.
- Very good adhesion on different types of construction materials such as concrete, mortar, fiber cement, brick, wood, steel, etc.
- Good abrasion and impact resistance.
- Resists washing and scrubbing with normal detergents.
Application data
- Recommended coverage per coat 4.1 m²/L (for 250 μm dry in one coat).
- Total recommended coverage 500 - 1000 g/m2 applied in 2 or 3 coats.
- Recommended dry film thickness 200-250 microns.
- Mixing ratio (by weight) 100/35 (A/B)
- Pot life (Pot life) 20 ºC 35-40 minutes
- Recoating time (20ºC RH: 60%) between 12 and 48 hours.
- Cleaning solvent Green solvent
* Performance factors are approximate and depend on the conditions of the substrate and the absorption capacity of the substrate.
Drying and start-up times
- Curing temperature 25ºC
- Repainting times: Minimum 12 hours Maximum 2 days
- Commissioning time: Pedestrian traffic 2 days Immersion 5 days Total cure 10 days
Important Note: Do not place the tank or reservoir in service until the coating is fully cured, approximately 10 days at 25°C, and has been thoroughly washed several times with potable water. Placement in service may be longer if curing temperatures are low or thicknesses are greater than specified.
Instructions for use
- The product is presented in pre-dosed batches, respecting the mixing ratio to the maximum and taking special care to drag the remains adhered to the bottom and walls of the container.
- The mixing operation of the components is carried out mechanically until a homogeneous mixture is obtained, using a low speed mixer (600 rpm) equipped with propellers that do not favor the entry of air and the formation of bubbles. First, each component is beaten separately and then the component from the small container or component B is poured into the large container or component A, beating the mixture until it is completely homogenized (approximately 1-2 minutes).
- Product to use, does not require dilution.
- It should be taken into account that the pot-life of the mixture depends on the temperature(the higher the temperature, the lower the pot-life and vice versa).
- Apply by roller, brush or spray ensuring the formation of a continuous layer without pores.
